High Performance Solvent Free Epoxy Resin Self - Leveling

DESCRIPTION
Deltafloor SL500 is a two – component solvent free epoxy resin self – leveling that suitable for top coat of epoxy resin flooring system. The cured film of Deltafloor SL500 forms a hard and smooth layer at thickness 500 micron with excellent adhesion to concrete substrate. The product is available in a wide range of standard colors and also provided to ensure the customer need.
 
USES
Deltafloor SL500 is recommended to areas where chemical resistance and aesthetic aspects are required. Deltafloor SL500 is recommended for use in floor of warehouse, industrial and food processing areas, kitchen, laboratory, engineering workshops, and car parks.

ADVANTAGES
Provides a seamless and jointless surface, easy to clean and maintain, hygienic, chemical resistance, excellent wear and abrasion resistance and have aesthetic state of art.

CONSUMPTION
Deltafloor SL500 consumption is 0.8 – 1 kg/m2 for 500 micron thickness. Please kindly contact DELTACRETE to have appropriate technical assistance for the recommended thickness since material performance may vary at different surface.

INSTRUCTION FOR USE
For best performance of Deltafloor SL500, please kindly follow our recommendation. Preparation is a must before application. For new concrete, allow the concrete to cure at least 28 days. Humidity is not more than 75% measured in accordance with BS 8203. Since Deltafloor SL500 is relatively thin coating, the substrate must be fine textured. Any surface irregularities may show through causing excessive wear on high spots. Concrete substrate must be structurally sound, clean, dry and free from all traces of loose material, laitance, oil and grease. Any unsound material must be removed before application. Preparation by captive blasting or diamond grinding is ideal for surface preparation. Priming using Deltaprime Series will enhance the adhesion of top coat with the concrete. The two component of Deltafloor SL500 by captive blasting or diamond grinding is ideal for surface preparation. Priming using Deltaprime Series will enhance the adhesion of top coat with the concrete. The two component of Deltafloor SL500 (component A and B) should be stirred individually before mixed together. Put both component in a mixing vessel and mix them thoroughly using low speed drill and mixing paddle mixer. Continue mixing process until a consistence homogeneous mixture achieved, normally it needed 3 – 5 minutes. Apply the mixed Deltafloor SL500 onto prepared surface using a brush or roller. Ensure that the area is completely coated and that ‘ponding’ material does not occur. Apply the second coat as soon as the first coat is initially dried (typically 5 – 6 hours).

CLEANING
Tools and equipment should be cleaned immediately after use, while the mixture are still un – cured with solvent cleaner. When mixture already harden, please kindly remove the material mechanically.

CURING TIME (at 30⁰ C)

TECHNICAL DATA

 
LIMITATIONS
Deltafloor SL500 should not applied on the surface known to, or likely to suffer from, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrate takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 10⁰C.

HEALTH AND SAFETY
Deltafloor range of products can cause skin irritations in persons with sensitive skin. Protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.  

FIRE
Deltafloor SL500 is non – flammable material.

Liquid Concrete Hardener

DESCRIPTION

DELTAHARD LCH is one component liquid concrete hardener based on metallic silicate with high silica content that can react chemically to produce a hard, abrasion resistant and dust-free finish. DELTAHARD LCH can be applied on any old or new floor concrete surface. It will absorp into the concrete surface and react with free lime and cement mortar forming a hard synthetic quartz-like material.

USES

• All concrete industrial floors, both old or new
• Car parks
• Warehouses
• Stores and shopping malls
• Schools and hospitals
• Concrete walls

ADVANTAGES

• Ready to use
• Easy to apply
• Non corrosive
• Improve chemical and abrasion resistant
• No peel, scratch or delaminate
• Fast drying
• Increase surface density and durability

APPLICATION Instruction

Surface Preparation

DELTAHARD LCH can be applied immediately after final finishing operations and when the concrete has hardened sufficiently at minimum 14 days of age. It can also be applied for old concrete.

The concrete surface must be clean and sound. Remove any dust, laitance, grease, oil, dirt, curing agents, impregnations, wax, coating and disintegrated material from surface. Grind the concrete to open the concrete pores. This will allow optimum penetration of DELTAHARD LCH

PRODUCT APPLICATION

Depending on size of work area, DELTAHARD LCH can be applied with a pump up sprayer or a high volume, low-pressure sprayer (HVLP). Apply DELTAHARD LCH to the surface evenly at the rate of approximately 80-200 m² per pail (20 kgs) or 4–10 m²/ 1 kg of Deltahard LCH. Lightly broom out any puddles immediately after the material has been applied. Allow DELTAHARD LCH to remain on the surface for 20-30 minutes. DO NOT LET ANY AREA DRY OUT during this time. Add more DELTAHARD LCH as needed in order to maintain a uniformly wet surface. After material has completely penetrated the surface, continue grinding and polishing to the intended final surface profile and desired finish. For best results, use an auto scrubber and water to remove residual slurry between abrasive disc grits.

CLEAN UP

Use water to clean tools and equipment. Treatment is environmentally friendly and requires no special or hazardous disposal methods.

TECHNICAL DATA

HEALTH AND SAFETY

DELTAHARD LCH is caustic materials which can be harmful to the skin and eye. During use, avoid contact with the skin or eyes. Wear suitable protective clothing – eye protectionand gloves. Good ventilation is necessary when applying DELTAHARD LCH. In case of contact with the skin, rinse with plenty of clean water, then cleanse thoroughly with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately.

FIRE

DELTAHARD LCH is non-flammable materials.

Water Based Floor

DESCRIPTION

Deltafloor FAB is a water-based emulsion that suitable for indoors and outdoors application. It has a good adhesion, abrasion resistance, free from metal, easy to apply, weather resistance because non yellowing like epoxy, easy to clean, and anti-slip. Deltafloor FAB is designed especially for sport court, carpark, sidewalk, city park, playground, and paving block.

USES

• Sportcourt
• Sidewalk
• Carpark
• Playground
• CityPark

ADVANTAGES

• Easytoapply
• Slipresistanceproperties
• AbrasionandWeatherresistance
• Excellentadhesiontoconcretesubstrate
• Trafficabletofoot,vehiclewithrubberorplastic wheel
• Fastcure
• Easytocleanand Noodor

APPLICATION PROCEDURE

Surface Preparations

Make sure the surface to be coated is dry, clean, free from dirt, rust, grease, oil, mould or any other loose material. It will be best to sweep away all the debris and dust before application. If the surface is still damp it will make the application easy to peel off. To make the adhesion even better, the surface should be primed with a Deltabond SB1.

If surface is smooth, it needs to buff it first and apply with DeltabondSB1.

Applications

Deltafloor FAB can be applied with brush or roller. Apply evenly to the substrate following the recommended dosage (0.3 kg/ m²) for two coats. The second coat can be applied after the first coat has started to set and can support the following coat. Usually, it only takes 5 – 10 minutes maximum, depending on the weather and humidity around. After applying two coats, it takes minimal 1 day to traffic foot and 2 -3 days to use for sport court.

LIMITATION

Deltafloor FABshould not submerged for a long time. Deltafloor FAB cannot be applied to water ponding areas.

PACKAGING

Deltafloor FAB is supplied in 4 kg in gallon and 20 kgs in pail.

Technical Data

CLEANING

The equipment after application should be removed with clean water.

STORAGE

Store in a dry and cool place. Protect against moisture. Store container in a well-ventilated place. The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable.

In this case however, the properties required for the intended use must be checked for quality assurance reasons

FIRE

Deltafloor FAB is non-flammable material.

CODE C10 – 08/23

Self levelling Cementitious Flooring

DESCRIPTION

Deltafloor CLT is a self levelling mortar as a material for facing concrete floor. It can be use for underlayment or overlayment applications. It is made from specially graded materials like cement, mineral fillers, binder and additive mixed homogenously. Deltafloor CLT is a powder form and available in light yellow colour.

When mixed with water, Deltafloor CLT is becomes a self – levelling compound which easy to apply either by hand or pump in thickness from 2 to 3 mm. After setting, in only a few hours, Deltafloor CLT has high early strength, dries quickly so that any further finishing may be applied after a very short time.

USES

Deltafloor CLT can be used to get levelling and smoothing floor. It is suitable for internal and eksternal application in industrial and public applications, such as :

1. For old or new floor, such as pedestrian traffic at shopping centres/ supermarkets, restaurants, appartments, show room, etc.

2. For receiving carpets, vinyl tiles, etc (Underlayment)

3. For industrial floors, such as chemical and processing plants, that must be protected with epoxy or water based paints flooring.

ADVANTAGES

• Easy to use for pumped or manual application
• Fast working time
• High early strength
• Good levelling
• Good adhesion on the substrates
• Cost effective

APPLICATION PROCEDURE

Surface Preparation

1. New concrete should be at least 7 days old or more
2. New and old concrete must be clean and free from contaminants, dust and dirt in order to obtain a good bond
3. Repair the holes on substrate

Priming

1. The prepared surface must be primed with Deltabond SB/ Deltabond SB1 using roller or brush with coverage 1 kg/4m².
2. Apply an even coat of Deltabond SB/ Deltabond SB1 after the first coat is completely dry.
3. Ensure the coat is dry before the next coat of primer or applying Deltafloor CLT.

Mixing

1. Pour 5.75 litres of water (23% of powder) into bucket
2. Pour 25 kgs (1 bag) of Deltafloor CLT into water
3. Mix for 2 – 3 minutes or until no agglomeration of Deltafloor CLT.

Application

1. Pour Deltafloor CLT mixture onto primed surface
2. Spread it with trowel
3. It is recommended that applicators wear spikes shoes during applications
4. Use spike roller to minimize the bubble/microfoam in Deltafloor CLT mixture
5. Coverage of Deltafloor CLT is 6 kg powder/m2 for 2 – 3 mm thick

Curing and Treatment

-       Under normal interior conditions, curing is not required

-       Where rapid drying conditions (high temperature, direct sunlight), it should be covered with plastic film for at least 1 or 3 days.

Cleaning

The equipment after application should be removed with clean water. Cured material can be removed mechanically, or with weak acid.

TECHNICAL DATA

STORAGE

Deltafloor CLT is cementitious based and has a shelf life of 6 months if stored in cool dry place and sealed packaging. Keep and avoid direct Deltafloor CLT from rain and sunlight.

LIMITATIONS

• Do not use Deltafloor CLT for heavy duty application
• Do not add cement or any admixture
• Do not use Deltafloor CLT on wet substrate
• Working life would be shortened at higher temperature

HEALTH AND SAFETY

• Avoid eye and skin contact as the product is alkaline
• Avoid inhalation of dust during mixing
• Wash thoroughly after handling
• In case of eye contact, flush with plenty of clean water. Seek medical help immediately.