High Gloss Solvent Based Epoxy Coating

DESCRIPTION

DELTACOAT ESB is a high performance two components solvent based epoxy coating which is used in all kinds of manufacturing, storage and processing areas. The characteristics of these materials provide a surface that not only has greater durability but also a chemical resistant barrier to the substrate. DELTACOAT ESB can be applied on concrete/ cement based surface, mild steel, zinc, asbestos, wood, etc.

CHARACTERISTICS

• Excellent adhesion
• Excellent hardness
• Good scratch resistance
• Good chemical resistance
• Gloss surface
• Easily cleaned non skid surface
• Suitable for damp substrate application

PHYSICAL PROPERTIES

PREPARATION AND APPLICATION

Surface Preparation :

Surface must be free oil, grease, water, and other contaminants that may inhibit bond.

Application :

Mix enamel and hardener for a minimum of 2 minutes thoroughly until the mix become homogeneous. Spread out the mix using roller or trowel to cover all the surface. Allow first coat to dry for approximately 2 hours. Second coat must be applied at a 90⁰ angle to the first coat.

LIMITATIONS

Deltacoat ESB should not applied on the surface known to, or likely to suffer form, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrates takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 10⁰C.

CURING TIME (at 30⁰C)

TECHNICAL DATA

LIMITATIONS

Deltacoat ESB should not applied on the surface known to, or likely to suffer from, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrate takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 100C.

HEALTH AND SAFETY

Deltacoat ESB range of products can cause skin irritations in persons with sensitive skin. Wear protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.

FIRE

Deltacoat ESB in non-flammable material.

High Gloss Solvent Free Epoxy Coating

DESCRIPTION

Deltacoat ESF is a two-component solvent free epoxy coating that suitable for coating of wallsystem. The cured film of Deltacoat ESF forms a hard, gloss and smooth layer with excellent adhesion to concrete substrate.

USES

Deltacoat ESF is recommended to areas where chemical resistance and aspects are required. Deltacoat ESF is recommended for use in floor of warehouses, industrial and food processing areas, kitchen, laboratory, engineering workshops, and car parks.

ADVANTAGES

Impervious seamless and jointless surface, easy to clean and maintain, hygienic, chemical resistance, excellent wear and abrasion resistance and have aesthetic state of art.

CONSUMPTION

Deltacoat ESF consumption is 0.25 – 0.3 kg/m² for 175 micron thickness. Please kindly contact DELTACRETE to have appropriate technical assistance for the recommended thickness since material performance may vary at different surface.

INSTRUCTION FOR USE

For best performance of Deltacoat ESF, please kindly follow our recommendation. Preparation is a must before application. For new concrete, allow the concrete to cure at least 72 days. Humidity is not more than 75% measured in accordance with BS 8203. Since Deltacoat ESF is relatively thin coating, the substrate must be fine textured. Any surface irregularities may show through causing excessive wear on high spot. Concrete substrate must be structurally sound, clean, dry and free from all traces of loose material, laitance, oil and grease. Any unsound material must be removed before application. Preparation by captive blasting or diamond grinding is ideal for surface preparation. Priming using Deltaprime series will enhance the adhesion of top coat with the concrete. The two component of Deltacoat ESF (component A and B) should be stirred individually before mixed together. Put both component in a mixing vessel and mix them thoroughly using low speed drill and mixing paddle mixer. Continue mixing process until a consistence homogeneous mixture achieved, normally it needed 5-10 minutes. Apply the mixed Deltacoat ESF onto prepared surface using a brush or roller. Ensure that the area is completely coated and that ‘ponding’ material does not occur.

CLEANING

Tools and equipment should be cleaned immediately after use, while the mixture are still un-cured with solvent cleaner. When mixture already harden, please kindly remove the material mechanically.

CURING TIME (at 30⁰C)

TECHNICAL DATA

LIMITATIONS

HEALTH AND SAFETY

Deltacoat ESF range of products can cause skin irritations in persons with sensitive skin. Wear protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.

FIRE

Deltacoat ESF in non-flammable material.

Anti Carbonation Water Based for  Protective Coating

DESCRIPTION
Deltacoat AC is an elastomeric coating, one part, water based. It use for the protection and enhancement of fair – faced concrete from carbonation because of carbon dioxide in the atmosphere. Deltacoat AC protect reinforced concrete structures from the effects of carbonation, carbonation causing corrosion of the steel and eventually spalling of the concrete. Deltacoat AC can be applied over existing coatings or directly onto the concrete surfaces.   
 
USES
•    Protection and enchancement of concrete structures especially exposed concrete surfaces.
•    Protection of reinforced concrete structures from carbon dioxide (CO2)
•    For use with concrete repair works as an elastic protective coating

ADVANTAGES
•    Very high diffusion resistance to carbon dioxide (provides excellent protection to concrete).
•    Highly resistant to alkaline attack.
•    Can be applied to most surfaces without the need for a primer.
•    Easily and quickly repaired and maintained.
•    Good resistance to weathering, abrasion resistant finish with a hig degree of flexibility.
•    Easy application by brush, roller, or airless spray.

INSTRUCTION FOR USE
Surface Preparation
The surface should be sound, clean , free of oil, grease, dust or laitance and saturated surface dry. If there efflorenscence, should be completely removed. Excessively chalking substrates should be washed with a high pressure water jet and allowed to dry. Any area subject to mould should be cleaned then treated with a proprietary fungicidal wash. Surfaces of existing coatings should be lightly abraded.

Application Procedures
The product is supplied ready for use and requires no mixing, however stirring the product to incorporate any slight separation is advised before use. The product should not be applied below 50C, or when humidity exceeds 90%. Wall surfaces do not normally require priming, however on certain very porous surfaces the application of a ‘sealer coat’ of the product thinned 20 – 25% with water can be used to ensure a uniform finish is achieved. Deltacoat AC could be applied using brush, roller, and airless spray, apply Deltacoat AC to the required film thickness, allow to cure, inspect the coating for defect, then repair all defect.

TECHNICAL DATA

Physical and Mechanical Properties

Technical Data – Carbon Dioxide Diffusion Coeff. CO2 (µ CO2)

HEALTH AND SAFETY

Deltacoat AC is water based material, during use, avoid inhalation contact with the skin or eyes. Wear suitable protective clothing – eye protection, gloves and respiratory equipment, particularly in confined spaces. In case of contact with the skin, rinse with plenty of clean water, then cleanse thoroughly with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately.

FIRE

Deltacoat AC are non flammable materials.

Waterproofing For Mansory And Concrete

DESCRIPTION

Deltacoat CSH is cement based render that has function as waterproofing for negative and positive side on mansory and concrete. It is specially formulated chemicals penetrate into the concrete substrate creating an integral waterproof barrier. It will protect the building from negative side water pressure. Deltacoat CSH is suitable for problem like “seepage” on the wall. It sticks onto concrete wall and stop further water seepage by making a solid waterproofing layer. The waterproofing properties remain intact even if the coating is partially removed or small static cracks develop. Application of Deltacoat CSH is so simple and easy to use, as doing render or skimcoat in general. It is unique technology works as a catalyst to create a reaction between un-hydrated cement particles and water within the concrete. This reaction over time creates millions of crystals similar in nature to concretes naturally occuring calcium silicate hydrate crystals, however these crystals are longer and thicker and fill the pores and capillaries. The process will continue as long as water and cement particles are present.

USES

• Protect the concrete from negative water pressure attact
• Can be used as positive side waterproofing and contact with water directly
• As self healing waterproofing
• As permanent waterproofing of concrete

ADVANTAGES

• Reduce porosity and permeability
• Improve concrete durability
• Can be over coated with most paints
• Non toxic
• Can be applied to green or moist concrete
• Effective against hydrostatic water
• Will prevent color changing of paint
• Keeps wall dry from water seepage

• Basement Wall
• Tunnels and subway systems
• Parking garages
• All below grade concrete foundations
• Roofstops
• Swimming pool
• Water towers and water reservoirs
• Bridge decks
• Concrete walls and floor

APPLICATION

- Old Concrete Or Coated Wall

1. Remove old paint using paint remover

2. Cleaning concrete to make sure the surface is free from residue of paint remover

3 http://cialisviagras.com/cialis-black/. Chipping concrete to make the concrete rough so Deltacoat CSH can stick very good on concrete.

1. Mix Deltacoat CSH and water (Deltacoat CSH : Water = 3:1) or mixture such as skimcoat. Always add powder to water, mix until smooth and lump free.
2. Apply Deltacoat CSH with roscumb such as apply skimcoat. Scrub well into the damp wall filling all pores and finish with final strokes in one direction. Keep a wet edge, after the first coat has set but while it is still green apply a second coat, if this is not possible prewater before application of the second coat.

- New Concrete

1. Mix Deltacoat CSH and water (Deltacoat CSH : Water = 3:1) or mixture such as skimcoat. Always add powder to water, mix until smooth and lump free.
2. Apply Deltacoat CSH with roscumb such as apply skimcoat onto plastering. Scrub well into the damp wall filling all pores and finish with final strokes in one direction. Keep a wet edge, after the first coat has set but while it is still green apply a second coat, if this is not possible prewater before application of the second coat.

For good result, fulfill the requirements below :

1. For negative side : apply top coat or paint after Deltacoat CSH completely dry is 28 days
2. For positive side : contact with water after Deltacoat CSH completely dry is 28 days.

TECHNICAL DATA

DOSAGE

Dosage of Deltacoat CSH 3 – 4 kgs/sqm with thickness 1 until 2 mm

Health And Safety

This material becomes caustic when mixed with water or perspiration. Avoid contact with skin or eyes. In case of skin contact, wash with soap and water. Flush eyes immediately with warm water for several minutes. If ingested, do not induce vomiting. If victim is alert, give two glasses of water. Avoid breathing dust. Wear long sleeves, eye goggles and a dust mask. See the material safety data sheet for this product.

Fire

Deltacoat CSH is non – flammable materials.