+62-21-344 2919      +62-21-3511 428      +62-811-9119-611   
    deltacrete@gmail.com      Senin - Jumat 9.00 - 17.00

Deltacoat ESB

High Gloss Solvent Based Epoxy Coating

DESCRIPTION

DELTACOAT ESB is a high performance two components solvent based epoxy coating which is used in all kinds of manufacturing, storage and processing areas. The characteristics of these materials provide a surface that not only has greater durability but also a chemical resistant barrier to the substrate. DELTACOAT ESB can be applied on concrete/ cement based surface, mild steel, zinc, asbestos, wood, etc.

CHARACTERISTICS

  • Excellent adhesion
  • Excellent hardness
  • Good scratch resistance
  • Good chemical resistance
  • Gloss surface
  • Easily cleaned non skid surface
  • Suitable for damp substrate application

PHYSICAL PROPERTIES

No. Item Enamel Hardener
1 Colour Available on request Clear to yellow
2 Appearance Liquid Liquid
3 Viscosity (cps) 700 - 3000 15 – 30
4 Solid content (%) 70 – 80 % 20 – 30%
5 Specific Gravity 1,45 ± 0,05 0,85 – 0,95

PREPARATION AND APPLICATION

Surface Preparation :

Surface must be free oil, grease, water, and other contaminants that may inhibit bond.

Application :

Mix enamel and hardener for a minimum of 2 minutes thoroughly until the mix become homogeneous. Spread out the mix using roller or trowel to cover all the surface. Allow first coat to dry for approximately 2 hours. Second coat must be applied at a 900 angle to the first coat.

Pot life (at 250C) = 4 hours
Coverage = 4 m2/kg (2 coats), thickness = 100µm
Setting/curing
Do not allow water or chemicals on the coated surface for a minimum of 72 hours.

LIMITATIONS

Deltacoat ESB should not applied on the surface known to, or likely to suffer form, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrates takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 100C.

CURING TIME (at 300C)

Pot Life 100 minutes
STT 4 hours
Initially hardness 9 hours
Fully cured after 3 days
(ambient temperature may have some effect on the curing time)

TECHNICAL DATA

Form Liquid (component A and B)
Viscoty Enamel 8580 cps
Viscoty Hardener 400 cps
Specific Gravity Mix 1.30 – 1.40
Shelf Life 1 year when unopened and stored in dry conditions
Packaging 4 kg set (Component A+B)
Comp. A (enamel) : 3 kg/can
Comp. B (hardener) : 1 kg/can

LIMITATIONS

Deltacoat ESB should not applied on the surface known to, or likely to suffer from, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrate takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 100C.

HEALTH AND SAFETY

Deltacoat ESB range of products can cause skin irritations in persons with sensitive skin. Wear protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.

FIRE

Deltacoat ESB in non-flammable material.

Our Location

PT. Deltacretindo Wira Mandiri
  JL. Pintu Air IV No. 41A
  Jakarta, Indonesia 10710
  +62-21-344 2919
  +62-21-3511 428
  +62-811-9119-611
   :  deltacrete@gmail.com

haki cm

© 2017 Deltacretindo. All Rights Reserved. Powered By GM-Portalindo