+62-21-344 2919      +62-21-3511 428      +62-811-9119-611   
    deltacrete@gmail.com      Senin - Jumat 9.00 - 17.00

Deltafloor HD5000

Heavy Duty Epoxy Resin Floor Mortar Screed

DESCRIPTION

A three-component 5 mm thick floor mortar screed based on solvent-free epoxy resins, bound together with non metallic natural aggregate with selected shape, grading, high physical quality and mechanical performance.

USES

Deltafloor HD5000 has been developed and designed for floor areas where high resistance to mechanical and chemical attack is required. It forms a non-slip, abrasion-resistant epoxy resin flooring of 5 mm thickness, which is ideal for medium to heavy duty industrial floors, workshop and factory floors, airport hangars, stairs, warehouses, traffic lanes, engineering workshops, and car parks.

ADVANTAGES

  • Easy to apply
  • Excellent adhesion to substrate
  • Provide long term protection in heavy industrial environments
  • Excellent resistance to abrasion
  • High mechanical strengths
  • Solvent free and good resistance to a wide range of industrial chemicals.

CONSUMPTION

Priming with Deltaprime Series at 0.2 – 0.3 kg/m2 in one coat of application. Consumption of Deltaprime series may vary due to the substrate condition

Mortar screed with Deltafloor HD5000 at 11 - 12 kg set (A+B+C)/m2 for 5 mm thickness.

If top coat is needed, apply Deltafloor TC301 at 0.5 kg/m2 for 300 micron thickness in two coats.

INSTRUCTION FOR USE

Substrate must be structurally sound, clean, dry and free from all traces of loose material, laitance, oil and grease. Any unsound material must be removed before application. Priming with Deltaprime Series and apply Deltafloor HD5000 when primer is still wet and tacky. For mixing Deltafloor HD5000, first stir all component A (enamel) with an electric stirrer prior to batching, then add all component B (hardener) into the mixer and mix them for 3 minutes at a low speed. Place some portion of component C (fillers) into the mixer and whilst mixing in progress, add the remaining portion of component C (fillers). Continue mixing process until a homogeneous and uniformly moist mix is obtained.

CURING TIME

Foot traffic 12 hours
For light vehicle traffic 2 days
Fully cured after 5 days

TECHNICAL DATA

Form Liquid (component A and B) and powder (component C)
Colour Natural
Mix Density 2.2 kg/l for finished screed
Strengths, 28 days Compressive strength : 600 kg/cm2
Tensile strength : 60 kg/cm2
Bond strength : 20 kg/cm2
Shelf Life 1 year when unopened and stored in dry conditions
Packaging 27.6 kg set (A+B+C)
Comp. A (enamel) : 1.7 kg/can
Comp. B (hardener) : 0.9 kg/can
Comp. C (filler) : 25 kg/bag

LIMITATIONS

Deltafloor HD5000 should not applied on the surface known to, or likely to suffer from, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrate takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 10°C. The concrete substrate when application should be at least 28 days old

HEALTH AND SAFETY

Deltafloor range of products can cause skin irritations in persons with sensitive skin. Wear protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.

FIRE

Deltafloor HD5000 and Deltaprime SF are non-flammable materials.

Deltafloor TC300 is flammable material. Keep away from source of ignition. No smoking. In the event of fire, extinguish with CO2 or foam.

Our Location

PT. Deltacretindo Wira Mandiri
  JL. Pintu Air IV No. 41A
  Jakarta, Indonesia 10710
  +62-21-344 2919
  +62-21-3511 428
  +62-811-9119-611
   :  deltacrete@gmail.com

haki cm

© 2017 Deltacretindo. All Rights Reserved. Powered By GM-Portalindo